The PicoScope 9200A oscilloscopes uses sequential sampling technology to measure fast repetitive signals without the need for expensive real-time sampling hardware. Combined with an input bandwidth of 12 GHz, this enables acquisition of signals with rise times of 50 ps or even faster. Precise timebase stability and accuracy, and a resolution of 200 fs, allow characterization of jitter in the most demanding applications.
The PicoScope 9200A scopes are designed with our PC Oscilloscope architecture to create a compact, lightweight instrument that can be easily carried around with your laptop.
10 GHz prescaled trigger
The PicoScope 9200A scopes have a built-in high-frequency trigger with frequency divider. Its typical bandwidth of up to 10 GHz allows measurements of microwave components with extremely fast data rates.
1 GHz full-function direct trigger
The scopes are equipped with a built-in direct trigger for signals up to 1 GHz repetition rate without using additional trigger units.
Built-in 2.7 Gb/s clock data recovery (CDR)
The PicoScope 9211A, 9221A, and 9231A have a dedicated clock recovery trigger input for serial data from 12.3 Mb/s to 2.7 Gb/s.
Pattern sync trigger and eye line
The PicoScope 9211A, 9221A and 9231A can internally generate a pattern sync trigger derived from bit rate, pattern length, and trigger divide ratio. This enables it to build up an eye pattern from any specified bit or group of bits in a sequence.
Eye line mode works with the pattern sync trigger to isolate any one of the 8 possible paths, called eye lines, that the signal can make through the eye diagram. This allows the instrument to display averaged eye diagrams showing a specified eye line.
8 GHz Optical to electrical converter
The PicoScope 9221A and 9231A have a built-in 8 GHz optical electrical converter. This allows analysis of optical signals such as SONET/SDH OC1 to OC48, Fibre Channel FC133 to FC4250, and G.984.2. The converter input accepts both single-mode (SM) and multimode (MM) fibers and has a wavelength range of 750 to 1650 nm.
Time Domain Reflectometer (TDR/TDT)
The PicoScope 9211A and 9231A TDR/TDT Oscilloscopes are specially designed for time-domain reflectometry (TDR) and time-domain transmissometry (TDT). It provides a low-cost method of testing cables, connectors, circuit boards and IC packages for unwanted reflections and losses.
The PicoScope 9211A and 9231A work by launching pulses into the device under test using programmable, 100 ps rise-time step generators. They then use their 12 GHz sampling inputs to build up a picture from a sequence of reflected or transmitted pulses. The results can be displayed as volts, ohms or rho against time or distance.
Built in signal generator
The scope can generate industry-standard or custom signals including clock, pulse and pseudo-random binary sequence. These can be used to test the instrument's inputs, experiment with its features and verify complex set-ups such as mask tests.
- 12 GHz (29 ps) Bandwidth
- 200 kS/s Sample Rate to 4 kS Store
- 200 fs, 5 THz Effective Sample Rate
- 10 GHz Prescaled & 1 GHz Direct Trigger
- Pattern Sync Trigger of Length 7 to 216–1
- 4 ps Typical RMS jitter
- 16 bit ADC Resolution
- Electrical standards compliance testing
- Semiconductor characterization
- Telecom service and manufacturing
- Timing analysis
- Digital system design and characterization
- TDR/TDT measurement and analysis
- Electronic mask drawing and display
- Automatic pass/fail limit testing
- High-speed serial bus pulse response
What's In The Box:
- (1) PicoScope 9200 Series PC sampling oscilloscope
- (1) PicoScope 9000 software CD
- (1) Quick start guide
- (1) 6 V power supply, universal input
- (1) Localized mains lead (line cord)
- (1) USB cable, 1.8 m
- (1) SMA / PC3.5 / 2.92 wrench
- (1) Storage and carry case
- (1) A170 18 GHz 50 Ω SMA(m-f) connector saver adaptor (one fitted to each input channel)